Maintain a well qualified computer

Damage to computer components is a very disturbing us. for example: damage to the motherboard , ram, power supply, vga, etc.. Damage to computers and the solution is an article that can be used as a reference for troubleshooting computer malfunction, including the following:

1. Computer Will not Live
solution:

1. Check the condition of the CPU power cable, monitor / LCD (stabilizer / UPS)
2. Check the CPU power cable is properly connected to a power source / / stabilizer / UPS
3. Check the monitor power cable / LCD is also well connected to the power source / stabilizer / UPS
4. Check the power cable to the UPS / stabilizer is connected to a power source (if using UPS / stbiliser)
5. If you still do not want to live permasalahanya may lie in the power supply or motherboard (if the power supply fan is off means there is an error in the power supply)

2. Computers Want But Do not Want Boot Life
Solutions:

1. Recognize First Beep Beep:

• Beep 1 time only good sign that the condition of the computer,
• Beep one time, long There are problems in memory
• Beep 1 time and 3 times the short-term damage on the VGA card,
• Beep 1 time long and 2 short times Damage in DRAM parity
• Damage continuous beep dimodul memory or video memory

1. Check with software dianosa like SiSoft Sandra, PC mark04, mark05 PC etc.

3. Computers Want Boot But Always "Safe Mode" (to go into safe mode press F8, delete, F2: each motherboard is different)
solution:

1. Restart your computer
2. If there is still a problem to reinstall windows on your computer
3. If still safe mode as well, meaning you Hardisk problem
   check with: scan disk

4. Computer Frequently Hang
solution:

1. Due to software crashes: press ctrl + alt + del >> click End Task on the program "Not Responding" press the restart button on the CPU
2. Hardware due to conflict (the addition of new hardware) hardware conflicts often occur in windows operating system: reinstall your windows, but to keep in mind before you reinstall windows, unplug your new hardware
3. Run facility "add new" hardware found on the control panel.

5. Keyboard or Mouse Not Recognized By Computer
Solutions:

1. Check wiring keyboard / mouse are installed correctly what has not
2. If it is but a keyboard / mouse is not detected then restart your computer and if you still touble try changing the keyboard / mouse and other computer restart
3. If the problem is also likely that the port is defective keyboard / mouse on your motherboard.
4. For the other way, you can change the model of keyboard / mouse USB. If there is still trouble, chances are your windows system error

6 . Computer Often Crash
Solution:

Check all wiring positions, hardware, and also stress on the chassis, check the temperature of the CPU and also check ram, processor and vga. 7. Forgot Password BIOS solution:

1. Cabut batterey cmos pada cpu
2. Moving Slot Jumper in BIOS / Clear CMOS, usually slot is located not far from the CMOS Battery on the motherboard. And usually it is marked with the letter slot CLR_CMOS. But before the move, please note the starting position Slot Jumper. If you've moved, turn on your PC (do not worry, if your PC does not light. Was it because you have changed the settings Clear CMOS Jumper.) If so, Unplug the PC and back again Slot Power Jumper to its original position. Then turn it back on ..
3. Trying to guess bberapa default password for multiple manufacturers eg AMI and AWARD bios (eg, AMI, AMI, AMI_SW, ALLY, 589 589 etc.)

8. Clock and date settings BIOS Always Turned-Change
Solution:

Batteray cmos is not working (dead), replace with a new batteray 9. Adding New Hardware Device, Tp Not Detected By BIOS solution: Most likely your bios outdated that it can not detect the new hardware, then immediately update your bios (can be downloaded via the internet, eg www.windrivers.com) 10. Keep track of Damage Card On Motherboard solution:

1. Try to unplug and plug in some cards on your MB
2. If the boot is successful then your card is not problematic so likewise vice versa

11. New Processor Plug Tp Not Detected
solution:

1. Check whether the type of the processor according to the processor slot motherboard
2. Check whether you have installed the processor correctly
3. Check whether the position of the jumpers on the processor are correct (about the jumper on the processor you can check the manual booknya)

12. Crash After Installing New RAM
solution:

Possible RAM you have installed is not compatible with your computer (unplug ram) 13. Adding RAM But Not Detected solution:

1. Make checks such as the previous case
2. Clean the other slot and move to other RAM slot
3. Make sure the RAM slots corresponding slot mainboard for example: SD RAM has almost the same slot RD RAM but RD RAM, can not be detected although it could be installed on the type of SD RAM slot.

14. After Adding RAM process Manjadi The Slow Computer
Solution:

Consider your ram capacity limit, for example, EDO ram type the maximum limit is 64 MB, so when forced to plus then your computer becomes increasingly slow 15. Monitor Will not Flash solution:

1. Make sure all the monitor power cable and vga connector associated with the CPU okay
2. Make sure the pin is also available on the go with the VGA port sempura nothing is bent, if not go all / one pin to VGA port
3. Also make sure your VGA card is ok

16. Being Dark Current Monitor Windows Loading
solution:

1. Likely due to monitor driver setup is not right (setting high frekuensinyaterlalu)
2. Go first to the conditions of safe mode (press F8, F2, delete etc.)
3. Install ulang runs VGAnya

17. Display Suddenly Become Corrupt And Computer Hang
Solution:

Due to the temperature (on the VGA card) is very hot, there is an error in the RAM 18. Monitor Display Size Mismatch Desire solution:

1. Go to display properties (right-click anywhere select properties)
2. Press tab and adjust the settings and display size as you wish (at screean area)

19. Currently Used As Flashing Monitor
solution:

1. Go to display properties (right-click anywhere select properties)
2. Press tab and click advanced settings, then click the adapter, in this section display the desired refresh rate

20. There is no sound (noise) that appears
Solution:

1. Make sure you have installed the motherboard drivers on the menu sound
2. If you use an external soundcard make sure you install it correctly
3. A crash with sound on board
4. Check the manual booknya, whether soundcard on boardnya need to be turned off or not if you want to re-install a new soundcard yan (usually can be turned off via jumper or bios It is no kompunen your computer as well as possible so that your computer remains the best possible condition, so keep the components critical darling in the computer.